Carbolite nanodac Manuel d'utilisateur Page 89
- Page / 122
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
nanodac™
87 MC27 –EN–1.04
RECORDER SPECIFICATION (Cont.)
USB port
Number of ports One at rear of instrument
Standard USB1.1
Transmission speeds 1.5Mbits/sec (low speed device)
Maximum current <100mA
Peripherals supported Memory stick (8GB max), Bar code reader, QWERTY keyboard
Update/Archive rates
Sample rate (input/output) 8Hz (4Hz for digital inputs) (4Hz for dual input channels)
Trend update 8 Hz max
Archive sample value Latest value at archive time
Display value Latest value at display update time.
9.2 ANALOGUE INPUT SPECIFICATION
General
Number of anaologue inputs Four
Input types Standard: dc Volts, dc mV, dc mA (external shunt required), thermocouple, RTD (2-wire and 3-wire), digital (contact closure).
Optional: dual mA, dual mV, dual thermocouple.
Input type mix Freely configurable
Sample rate 8Hz (125ms)
Conversion method 16 bit delta sigma.
Input ranges See below.
Mains rejection (48 to 62Hz)
Series mode: >95dB
Common mode: >179dB
Common mode voltage 250Vac max.
Series mode voltage 280mV at lowest range; 5V peak-to-peak, at highest range.
Input impedance See relevant Range specification, below.
Overvoltage protection Continuous: ± 30V RMS
Transient (<1ms): ±200V pk-pk between terminals.
Sensor break detection Type ac sensor break on each input giving quick response with no associated dc errors.
Recognition time: <3 secs.
Minimum break resistance: 40mV, 80mV ranges: 5kΩ; other ranges: 12.5kΩ
Shunt (mA inputs only) Values 1Ω to 1kΩ, mounted externally.
additional error due to shunt: 0.1% input
Isolation Channel to channel: 300V RMS or dc (double insulation)
Channel to common electronics: 300V RMS or dc (double insulation)
Channel to ground: 300V RMS or dc (double insulation)
Dielectric strength Test: BS EN61010, 1 minute type test
Channel to channel: 2500 Vac
Channel to ground: 1500 Vac
DC input ranges
Ranges 40mv, 80mV, 2V; 10V (-4.0 to +10V)
40mV Range Range: -40mV to + 40mV
Resolution 1.9μV (unfiltered)
Measurement noise: 1.0μV peak-to-peak with 1.6s input filter
Linearity error: 0.003% (best fit straight line)
Calibration error: ±4.6μV ±0.053% of measurement at 25°C ambient
Temperature coefficient: ±0.2μV/°C ± 13ppm/°C of measurement from 25°C ambient
Input leakage current: ±14nA
Input resistance: 100MΩ
80mV Range Range: -80mV to + 80mV
Resolution 3.2μV (unfiltered)
Measurement noise: 3.3μV peak-to-peak with 1.6s input filter
Linearity error: 0.003% (best fit straight line)
Calibration error: ±7.5μV ±0.052% of measurement at 25°C ambient
Temperature coefficient: ±0.2μV/°C ± 13ppm/°C of measurement from 25°C ambient
Input leakage current: ±14nA
Input resistance: 100MΩ
2V Range Range: ±2V
Resolution 82μV
Measurement noise: 90μV peak-to-peak with 1.6s input filter
Linearity error: 0.003% (best fit straight line)
Calibration error: ±420μV ±0.044% of measurement at 25°C ambient
Temperature coefficient: ±125μV/°C ± 13ppm/°C of measurement from 25°C ambient
Input leakage current: ±14nA
Input resistance: 100MΩ
- Operating Instructions 1
- Contents 3
- 2. Login 5
- MC27 –EN– 1.04 4 6
- 3. Cascade 7
- OVER-TEMPERATURE CONTROL 8
- 4. OPERATION 9
- 9 MC27 –EN–1.04 11
- 11 MC27 –EN–1.04 13
- MC27 –EN– 1.04 12 14
- 13 MC27 –EN–1.04 15
- 4.3 TOP LEVEL MENU 16
- 15 MC27 –EN–1.04 17
- Page key 18
- Scroll key 18
- 17 MC27 –EN–1.04 19
- 19 MC27 –EN–1.04 21
- 21 MC27 –EN–1.04 23
- 4.4 DISPLAY MODES 24
- 23 MC27 –EN–1.04 25
- 25 MC27 –EN–1.04 27
- 27 MC27 –EN–1.04 29
- 29 MC27 –EN–1.04 31
- 31 MC27 –EN–1.04 33
- 35 MC27 –EN–1.04 37
- 37 MC27 –EN–1.04 39
- 41 MC27 –EN–1.04 43
- 45 MC27 –EN–1.04 47
- 47 MC27 –EN–1.04 49
- Enter trend history mode 51
- Press and hold scroll 53
- 5. CONFIGURATION 54
- 53 MC27 –EN–1.04 55
- 55 MC27 –EN–1.04 57
- 57 MC27 –EN–1.04 59
- 5.2 GROUP CONFIGURATION 60
- 59 MC27 –EN–1.04 61
- 6. iTOOLS 62
- 63 MC27 –EN–1.04 65
- 65 MC27 –EN–1.04 67
- 6.3 PARAMETER EXPLORER 67
- Explorer menu 68
- Context menu 68
- 67 MC27 –EN–1.04 69
- 6.4 WATCH/RECIPE EDITOR 70
- 69 MC27 –EN–1.04 71
- 6.5 PROGRAMMER OPTION 72
- 71 MC27 –EN–1.04 73
- 73 MC27 –EN–1.04 75
- 75 MC27 –EN–1.04 77
- 77 MC27 –EN–1.04 79
- Figure 3.6.10a 80
- Figure 3.6.10b 80
- Figure 3.6.10c 80
- 79 MC27 –EN–1.04 81
- Figure 3.6.10f 82
- 7. USER WIRING 83
- 7.1 COUNTER EXAMPLE 84
- 8. USB DEVICES 87
- 9.1 RECORDER SPECIFICATION 88
- 87 MC27 –EN–1.04 89
- Table A3a RTD type details 90
- 89 MC27 –EN–1.04 91
- 10.1 Autotune 91
- 91 MC27 –EN–1.04 93
- 93 MC27 –EN–1.04 95
- OP Power 96
- Temperature 96
- 95 MC27 –EN–1.04 97
- ′) at this point 98
- 97 MC27 –EN–1.04 99
- 1200 = 120 99
- 11. Appendix C: REFERENCE 100
- 99 MC27 –EN–1.04 101
- C2.1 DOWNLOADING 101
- 101 MC27 –EN–1.04 103
- C2.2 SERVER SETUP 103
- C2.3 PC SETUP 104
- 103 MC27 –EN–1.04 105
- C2.5 ARCHIVE ACTIVITY 105
- 12. Appendix E: WEB SERVER 106
- 105 MC27 –EN–1.04 107
- 12.5 Home Page 107
- 12.6 About Page 107
- 12.7 Contact Page 107
- 12.8 Bar Graph Page 108
- 107 MC27 –EN–1.04 109
- 12.9 Line Graph Page 109
- 12.10 Numeric Page 110
- 12.11 Alarm Summary Page 110
- 109 MC27 –EN–1.04 111
- 12.12 Message Summary Page 111
- 12.13 Promote Page 111
- 12.14 Historical Line Page 112
- 111 MC27 –EN–1.04 113
- 12.15 Status Icons 113
- 12.16 DHCP Support 113
- 12.17 Network Protocols 113
- 12.18 Languages 113
- 113 MC27 –EN–1.04 115
- 115 MC27 –EN–1.04 117
- 117 MC27 –EN–1.04 119
- MC27 –EN– 1.04 118 120
- MC27 –EN– 1.04 120 122
Produits connexes et manuels pour Panneau de contrôle Carbolite nanodac
(12 pages)
Panneau de contrôle Carbolite 2116 used for over temperature protection Manuel d'utilisateur
(4 pages)
(4 pages)
Panneau de contrôle Carbolite 2116 used for over temperature protection Manuel d'utilisateur
(4 pages)
(4 pages)
(28 pages)
(28 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.171 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels